(021) 839-5163 / 5164 
sales@capelabsupplies.co.za

Concrete

The TCM-0075 Manual Mortar Mixer has a 5 litre (approx.) capacity, it has been designed to mix mortars and cement pastes primarily to the requirements of standards. The mixing paddle revolves at a rate of 140 rpm. With a planetary motion of 62 rpm in low speed. In high speed, the paddle revolves at the [Read More]

SAFE – GUARD YOUR LAB EQUIPMENT !   AUTOMATIC VOLTAGE STABILISER Our Automatic Voltage Stabilizers are designed to work in the most rugged and tempremental  conditions. They are best used on site laboratories where low and high voltage conditions are experienced frequently. FEATURES High Precision Single and three phase models Analogue display Fully automatic Minimal [Read More]

Air Entrainment Meter 8 L For determining the total air content in fresh concrete. Air entrainment meter cap. 8 l, manually operated pump for freshly mixed concrete direct reading in % DIN 1048, ASTM C231, BS 1881, DIN EN 12350-7   Technical Features Pushbuttons for simple performance of the test. Mechanical valve for secure and [Read More]

Specification: The apparatus consists of a double wooden table measuring 700×700 mm and hinged at one side. The top table is covered with a flat metal plate 2 mm thick, inscribed, and protected against corrosion. The galvanised steel cone has a top 130 mm dia., base 200 mm dia., and is 200 mm high. Supplied [Read More]

Rifflers / Sample Splitters The use of a riffler/sample splitter is for rapid preperation of representative samples. Made of sheet metal. Each riffler/sample splitter is suppled with three metal receiving pans.                RIFFLER SIZES  Nuber of Slots      Slot Width 20 Slots         6,7 mm 20 Slots         7,0 mm 20 Slots        12,5 mm 20 [Read More]

Marsh Flow Cone Used to dertine the fluidity of mortar flowing through the spout of a standard cone. 2L Plastic container, base Stand, 10 and 152mm diameter stainless steel cone (28 angle), height 280mm. Stainless steel sieve diameter150mm with 1,5mm mesh. Supplied with four interchangable stainless steel spouts 8, 9, 10 and 11mm.

Slump Test Equipment Used to determine the consistency of concrete mixes having medium and high workability.   Slump Cone made from galvanised sheet steel Dimensions 200 x 100 x 300mm (H)   Steel tamping rod, dia 16 x 600mm (L)   Slump  Metal Base Plate 450 x 450mm   300mm S/Steel Ruler   Scoop 310mm [Read More]

Test Sieves The ranges of 75mm, 100mm and 200mm sieves are supplied with full-depth stainless steel frames. The 300mm and 450mm sieves are supplied with plated, mild steel frames. Woven wire and perforated plate sieves are manufactured from stainless steel mesh or plated mild steel.   A full range of diamond sieves in 100mm and [Read More]

   NON – DESTRUCTIVE TESTING    Concrete Test Hammer    Used to obtain an estimate of strength and quality of hardened concrete.    Supplied complete with carborundum stone and plastic carrying case.    Strength range 10 to 70 N/mm2 (100 to 700 kgf/cm2)      Test Anvil     Made of special steel, for routine checks [Read More]

           CUBE MOULDS              Available in different materials: Accurately machined cast iron and steel. High precision moulds.  Rigid plastic/polyurethane, stable and resistant, compressed air (2 bar) or water jet is sufficient for extrusion.     Cement Mould Cube 70mm/side Plastic – Three gang Cube 70mm/side Steel – Three gang Three gang prism mould [Read More]

Contact Us For All Your Lab Needs!

We have over 60 years experience in the material testing field and have a product range of over 3000 items, if you do not find what you need on here then contact us!